Defi Xpress Patient Monitor

Defi® Xpress is a defibrillator with Multi parameter Patient Monitor with voice alarm that meets your clinical needs from Basic Life Support (BLS) to Advanced Cardiac Life Support (ACLS).
Manual defibrillator 2J-360J ,AED 50-200J
Multi-parameter patient monitor ECG.SpO2.NIBP.EtCO2.Pacer.
Available colour
Grey/Blue/White
Defibrillators benefit patients who experience a sudden heartbeat (arrhythmia). In these cases
Defibrillators are an important tool for anyone who is near a victim suffering from a ventricular arrhythmia. The arrhythmia causes the patient to lose consciousness. The expected outcome of such an arrhythmia is either cardiac arrest or stroke.

Description

Defi® Xpress is a defibrillator with Multi parameter Patient Monitor with voice alarm that meets your clinical needs from Basic Life Support (BLS) to Advanced Cardiac Life Support (ACLS).
Manual defibrillator 2J-360J ,AED 50-200J
Multi-parameter patient monitor ECG.SpO2.NIBP.EtCO2.Pacer.
Available colour
Grey/Blue/White
Defibrillators benefit patients who experience a sudden heartbeat (arrhythmia). In these cases
Defibrillators are an important tool for anyone who is near a victim suffering from a ventricular arrhythmia. The arrhythmia causes the patient to lose consciousness. The expected outcome of such an arrhythmia is either cardiac arrest or stroke.

Descriptions

High resolution 8 inch TFT color display
Energy selection: 2,5,7,10,20,30,50,70,100,150,200,300,360 Joule
Defibrillator device voice alarm
Charge time: Less than 7 seconds with a new, fully charged battery
Energy display: monitor display shows both selected and delivered energy
Charging prompts: Voice and visual prompts
Electrode impedance measurement range: 0-250 ohms
Manual mode
Built-in printer
Reusable standard external adult and pediatric paddles (pediatric paddles integrated)
AED function: Automatic analysis and chargingx3 with programmable automatic energy level selection
Output waveform: Biphasic technology
Standard Parameter is ECG: I II III AVR AVL AVF V

Options:
SpO2, NIBP module, EtCO2 module, Pacemaker, Trolley, Carrying case

Parameter

This section describes the electromagnetic compatibility and rhythm detection performance of the physical electronic isolation defibrillator battery:

Data acquisition and analysis

The Defi® Xpress is no longer automatically set to a specific frequency response. There are two diagnostic frequency options: 0.05-150 Hz
Diagnostic frequency filter and 0.05-40 Hz filtered diagnostic
Frequency filter. See Chapter 7 to switch between these two options.

Defibrillator

Waveform Details:
The tables below detail the waveforms that the Defi® Xpress delivers when connected to resistive loads of 25, 50, and 100 ohms and set to its maximum output power.
The waveforms are identified by the peak current (Ip) values DEFI XPRESS for two-phase operation: Duration of the first output phase (tphase1) and Duration of the second output phase (tphase2).
The specified values are within 10%.
Waveform: Truncated exponential curve Biphasic

Output energy accuracy:
+/- 10% or 1J (whichever is greater) at 50 ohms
+/- 15% or 1J (whichever is greater) at 25 to 100 ohms

Energy Selection:
External: 2 5 7 10 20 30 50 70 100 150 200 300 360 J.

Recharge time: < 06 seconds at 200 J (with a Ni- MH 12 volt – MEDITECH battery). < 12 seconds @ 360 J (with a Ni- MH 12 volt – MEDITECH battery after 15 dischargesafter15discharges). < 15 seconds @ 360 J (without a battery 90% AC mains voltage)
Charge level indication: Audible and graphic.

Output :
Adult paddle, pediatric adapter and multipurpose hands-free adapter available.
Synchronizer : Delivers power within 60 msec.
Disarm: Front panel switch.

Monitor/Display

Input:
3-wire 5-core patient cable
Size: 8 inch
Type: Color (TFT)
Display resolution: 800 x 600 pixels.
Passing speed: 12.5mm/s25mm/s50mm/s
Lead selection: I II III AVR AVL AVF V.
Frequency response: (user selectable).
0.7 to 20 Hz Operating mode
0.3 to 40 Hz Monitoring mode
0.05 to 150 Hz Analysis mode
0.5 to 30 Hz AED mode
Common mode rejection: > =60dB
Heart rate monitor: 20 to 300 BPM.
Heart rate alarms: user selectable.
Size: 0.125 0.25 0.5 1 2 4 cm/mv and auto ranging.
ECG output: 1 V/mv.
Heart Rate Response to Irregular Rhythm: (AAMI EC13-1992 Section 4.1.2.1.e.)

Alarms

Heart Rate Spo2 Alarm:
Audible: 5-pulse 800 tone with a PW of 150 msec, a PRI of 225 msec, and a repeat interval of 10 seconds.
Visual: The heart rate alarm flashes the displayed heart rate at 2 Hz. This indicator is located at the top of the display and is 0.4″ high and 0.28 to 0.840″ wide, depending on the number of digits in the heart rate. It is amber, black, white, or the color of the display text.

Line fault alarm:
Audible: triplet tone with 3 pulses and 500 Hz with a PW of 200 msec and a PRI of 310 msec. If the HR alarm is set or the pacemaker is turned on, the line fault tone repeats at a 20 second repetition interval.
Visual: When a line fault occurs, the message “LEAD FAULT” is displayed on the trace along with a dashed line the width of the trace. The text is 0.18″ high and is the color of the display text. The dashed line is 5″ long and has the width of the display. The signal is not modulated.

Physiological alarms (Spo2) (options):
Audible: See heart rate alarm
Visual: Physiological alarms flash the displayed parameter at 2 Hz. The color is amber, white, or the same as the colored text on the display.
Mute Duration: 90 seconds.

NIBP (options):
Method: automatic oscillation
Working mode: manual/automatic
Measurement: adult: 10-250mmHg
Ement: pediatric: 10-200mmHg
Ement: neonatal: 10-135mmHg

End-tidal CO2 (EtCO2):
Safety EtCO2:BF type
Current consumption 12.0V±0.2V DC
Current consumption 100mA (typical with pump on) 200mA (extreme condition)
Operating temperature range 5~50℃
Shipping/storage temperature range -20~+70℃
Relative humidity 0-85% (non-condensing)
Dimensions 96×91×36mm
CO2 range 0 to 13%(0-98.8mmHg@BTPS)
CO2 accuracy < 5.0% CO2 (at BTPS) ± 3 mmHg > 5.0% CO2 (at BTPS) < 10% of reading
Respiratory rate 3~60 BPM
Measurement accuracy ±1 BPM
Warm-up time 10 seconds
Detector response time: 10mS,
System: depends on implementation, pneumatics and water separation technology
Flow control 50~250ml/min
Interface Highly configurable serial digital interface (TTL/RS232)
Automatic offset calibration time and temperature dependent and as required

Pacemaker (options)
Type: VVI
Pulse type: rectangular, constant current
Pulse amplitude: 0 to 180 mA ± 10% or 5 mA (whichever is greater).
Pacing frequency: Variable from 30 ppm to 180 ppm ±1.5% (increments or decrements by a value of 2 ppm)
Multi-Functional Electrode: (MFE) Pads: Multipurpose defibrillation/pacing electrodes
Pause: pacing pulse rate is reduced by a factor of 4 upon activation
Refractory period: NC (VVI requirements do not have this specification)
Pulse width: (20+ 1.5 ms)
Output protection: Fully defibrillator protected and isolated

Recorder
Type: High resolution thermal array.
Recording: time date ECG lead ECG gain heart rate defibrillation and treatment summary ACLS events.

Configuration List

Standard:

ECG Cable (5 Leads) …… 1 Pcs
AED Pad Adapter ……….. 1 Pcs
AED Pad ……………………..1 pcs
Ground Cable ……………. 1 Pcs
Power Cable ………………. 1 Pcs
Thermal Paper Role …….. 1 Pcs
Cleaning Cloth ……………. 1 Pcs

Reviews

There are no reviews yet.

Be the first to review “Defi Xpress Patient Monitor”

Your email address will not be published. Required fields are marked *

Post comment